| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This removes the direct WME info access in the ieee80211com struct and instead
provides a method of fetching the data. Right now it's a no-op but eventually
it'll turn into a per-VAP method for drivers that support it (eg iwn, iwm,
upcoming ath10k work) as things like p2p support require this kind of behaviour.
Tested:
* ath(4), STA and AP mode
TODO:
* yes, this is slightly stack size-y, but it is an important first step
to get drivers migrated over to a sensible WME API. A lot of per-phy things
need to be converted to per-VAP before P2P, 11ac firmware, etc stuff shows up.
Notes:
svn path=/head/; revision=327479
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Notes:
svn path=/head/; revision=326255
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
software/hardware queue TID mapping.
When I initially did this 11n TX work in days of yonder, my 802.11 standards
clue was ... not as finely tuned. One of the things in 802.11-2012 (which
I guess technically was after I did this work, but I'm sure it was like this
in the previous rev?) is that among other traffic classes, three things are
important:
* group addressed frames should be default non-QoS, even if they're QoS frames, and
* group addressed frames should have a seqno out of a different space than the
per-TID QoS one; and because of this
* group addressed frames, being non-QoS, should never be in the Block-ACK window
for TX.
Now, net80211 and now this code cheats by using the non-QOS TID, but ideally
we'd introduce a separate seqno space just for multicast/group traffic for
TX and RX comparison.
Later extensions (eg reliable multicast / multimedia) express what one should do
when doing multicast traffic in a TID. Now, technically we /could/ do group traffic
as QoS traffic and throw it into a per-TID seqno space, but this definitely
introduces ordering issues when you take into account things like CABQ behaviour.
(Ie, if some traffic in the TID goes into the CABQ and some doesn't, because
it's doing a split of multicast and non-multicast traffic, then you have
seqno ordering issues.)
So, until someone implements 802.11vv reliable multicast / multimedia extensions,
group traffic is non-QoS.
Next, software/hardware queue TID mapping. In the past I believed the WME tagging
of frames because well, net80211 had a habit of tagging things like management
traffic with it. But, then we also map QoS traffic categories to TIDs as well.
So, we should obey the TID! But! then it put some management traffic into higher
WME categories too, as those frames don't have QoS TIDs. But! It'd do things like
put things like QoS action frames into higher WME categories, when they should
be kept in-order with the rest of the traffic for that TID. So! Given all of this,
the ath(4) driver does overrides to not trust the WME category.
I .. am undoing some of this. Now, the TID has a 1:1 mapping to the hardware
queue. The TID is the primary source of truth now for all QoS traffic.
The WME is only used for non-QoS traffic. This now means that any TID traffic
queued should be consistently queued regardless of WME, so things like the
"TX finished, do more TX" that is occuring right now for transmit handling
should be "better".
The consistent {TID, WME} -> hardware queue mapping is important for
transmit completion. It's used to schedule more traffic for that
particular TID, because that {many TID}:{1 TXQ} mapping in ath_tx_tid_sched()
is used for driving completion. Ie, when the hardware queue completes,
it'll walk that list of scheduled TIDs attached to that TXQ.
The eventual aim is to get ready for some other features around putting
some data into other hardware queues (eg for better PS-POLL support,
uAPSD, support, correct-er TDMA support, etc) which requires that
I tidy all of this up in preparation for then introducing further
TID scheduling that isn't linked to a hardware TXQ (likely a per-WME, per-TID
driver queue, and a per-node driver queue) to enable that.
Tested:
* AR9380, STA mode
* AR9380, AR9580, AP mode
Notes:
svn path=/head/; revision=315531
|
| |
|
|
|
|
|
| |
This is just to improve adrian-debugging.
Notes:
svn path=/head/; revision=313026
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
populate hardware frames
This is two fixes, which establishes what I /think/ is pretty close to the
theoretical PHY maximum speed on the AR9380 devices.
* When doing A-MPDU on a TID, don't queue to the hardware directly if
the hardware queue is busy. This gives us time to get more packets
queued up (and the hardware is busy, so there's no point in queuing
more to the hardware right now) to potentially form an A-MPDU.
This fixes up the throughput issue I was seeing where a couple hundred
single frames were being sent a second interspersed between A-MPDU
frames. It just happened that the software queue had exactly one
frame in it at that point. Queuing it until the hardware finishes
transmitting isn't exactly costly.
* When determining whether to dequeue from a software node/TID queue into
the hardware queue, fix up the checks to work right for EDMA chips
(ar9380 and later.) Before it was not dispatching anything until
the FIFO was empty. Now we allow it to dispatch another aggregate
up to the hardware aggregate limit, like I intended with the earlier
work.
This allows a 5GHz HT40, short-GI, "htprotmode off" test at MCS23
to achieve 357 Mbit/sec in a one-way UDP test. The stars have to be
aligned /just right/ so there are no retries but it can happen.
Just don't expect it to work in an OTA test if your 2yo is running
around the room - MCS23 is very very sensitive to channel conditions.
Tested:
* AR9380 STA (test) -> AR9580 hostap
TODO:
* More thorough testing on pre-AR9380 chips (AR5416, AR9160, AR9280)
* (Finally) teach ath_rate_sample about throughput/latency rather than
air time, so I can get good transmit rates with a 2yo running around.
Notes:
svn path=/head/; revision=312661
|
| |
|
|
|
|
|
|
|
|
| |
This field may be used for received frames only.
Differential Revision: https://reviews.freebsd.org/D3826
Differential Revision: https://reviews.freebsd.org/D3827
Notes:
svn path=/head/; revision=306049
|
| |
|
|
|
|
|
|
|
|
| |
* Don't do RTS/CTS - experiments show that we get ACK frames for each of them
and this ends up causing the timestamps to look all funny.
* Set the HAL_TXDESC_POS bit, so the AR9300 HAL sets up the hardware to return
location and CSI information.
Notes:
svn path=/head/; revision=305721
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The pre-11n calculations include SIFS, but the 11n ones don't.
The reason is that (mostly) the 11n hardware is doing the SIFS calculation
for us but the pre-11n hardware isn't. This means that we're over-shooting
the times in the duration field for non-11n frames on 11n hardware, which
is OK, if not a little inefficient.
Now, this is all fine for what the hardware needs for doing duration math
for ACK, RTS/CTS, frame length, etc, but it isn't useful for doing PHY
duration calculations. Ie, given a frame to TX and its timestamp, what
would the end of the actual transmission time be; and similar for an
RX timestamp and figuring out its original length.
So, this adds a new field to the duration routines which requests
SIFS or no SIFS to be included. All the callers currently will call
it requesting SIFS, so this /should/ be a glorious no-op. I'm however
planning some future work around airtime fairness and positioning which
requires these routines to have SIFS be optional.
Notably though, the 11n version doesn't do any SIFS addition at the moment.
I'll go and tweak and verify all of the packet durations before I go and
flip that part on.
Tested:
* AR9330, STA mode
* AR9330, AP mode
* AR9380, STA mode
Notes:
svn path=/head/; revision=302877
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is the initial framework to call into the MCI HAL routines and drive
the basic state engine.
The MCI bluetooth coex model uses a command channel between wlan and
bluetooth, rather than a 2-wire or 3-wire signaling protocol to control things.
This means the wlan and bluetooth chip exchange a lot more information and
signaling, even at the per-packet level. The NICs in question can share
the input LNA and output PA on the die, so they absolutely can't stomp
on each other in a silly fashion. It also allows for the bluetooth side
to signal when profiles come and go, so the driver can take appropriate
control. There's also the possibility of dynamic bluetooth/wlan duty cycle
control which I haven't yet really played with.
It configures things up with a static "wlan wins everything" coexistence,
configures up the available 2GHz channel map for bluetooth, sets a static
duty cycle for bluetooth/wifi traffic priority and drives the basics needed to
keep the MCI HAL code happy.
It doesn't do any actual coexistence except to default to "wlan wins everything",
which at least demonstrates that things do indeed work. Bluetooth inquiry frames
still trump wifi (including beacons), so that demonstrates things really do
indeed seem to work.
Tested:
* AR9462 (WB222), STA mode + bt
* QCA9565 (WB335), STA mode + bt
TODO:
* .. the rest of coexistence. yes, bluetooth, not people. That stuff's hard.
* It doesn't do the initial BT side calibration, which requires a WLAN chip
reset. I'll fix up the reset path a bit more first before I enable that.
* The 1-ant and 2-ant configuration bits aren't being set correctly in
if_ath_btcoex.c - I'll dig into that and fix it in a subsequent commit.
* It's not enabled by default for WB222/WB225 even though I believe it now
can be - I'll chase that up in a subsequent commit.
Obtained from: Qualcomm Atheros, Linux ath9k
Notes:
svn path=/head/; revision=301181
|
| |
|
|
|
|
|
|
|
| |
No functional change.
Reviewed by: adrian
Notes:
svn path=/head/; revision=298939
|
| |
|
|
|
|
|
|
| |
I saw this happen a couple of times and all I saw was a dump of the
transmit descriptors. Log the message for now so I can see whta happened.
Notes:
svn path=/head/; revision=298761
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
ieee80211_raw_output().
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
Notes:
svn path=/head/; revision=289165
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
Notes:
svn path=/head/; revision=289162
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Notes:
svn path=/head/; revision=287197
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
references to ic->ic_softc.
This is in preparation for gleb's ifnet work.
Tested:
* ath(4), STA mode
* ath(4), hostap mode
* make universe
Notes:
svn path=/head/; revision=286835
|
| |
|
|
|
|
|
|
|
|
|
|
| |
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
Notes:
svn path=/head/; revision=286437
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
Notes:
svn path=/head/; revision=286410
|
| |
|
|
| |
Notes:
svn path=/head/; revision=283744
|
| |
|
|
| |
Notes:
svn path=/head/; revision=271823
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
Notes:
svn path=/head/; revision=265115
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The existing cleanup code was based on the Atheros reference driver
from way back and stuff that was in Linux ath9k. It turned out to be ..
rather silly.
Specifically:
* The whole method of determining whether there's hardware-queued frames
was fragile and the BAW would never quite work right afterwards.
* The cleanup path wouldn't correctly pull apart aggregate frames in the
queue, so frames would not be freed and the BAW wouldn't be correctly
updated.
So to implement this:
* Pull the aggregate frames apart correctly and handle each separately;
* Make the atid->incomp counter just track the number of hardware queued
frames rather than try to figure it out from the BAW;
* Modify the aggregate completion path to handle it as a single frame
(atid->incomp tracks the one frame now, not the subframes) and
remove the frames from the BAW before completing them as normal frames;
* Make sure bf->bf_next is NULled out correctly;
* Make both aggregate session and non-aggregate path frames now be
handled via the incompletion path.
TODO:
* kill atid->incomp; the driver tracks the hardware queued frames
for each TID and so we can just use that.
This is a stability fix that should be merged back to stable/10.
Tested:
* AR5416, STA
MFC after: 7 days
Notes:
svn path=/head/; revision=264720
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MAC
* Now that the paused < 0 bugs have been identified, make the DPRINTF()
a device_printf() again. Anything else that shows up here needs to be
fixed immediately.
Tested:
* AR5416, STA mode
MFC after: 7 days
Notes:
svn path=/head/; revision=264711
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
frame through the cleanup path.
Whilst here, fix the indenting for something I messed up.
Tested:
* AR5416, STA mode
Notes:
svn path=/head/; revision=264710
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
During power save testing I noticed that the cleanup code is being
called during a RUN->RUN state transition. It's because the net80211
stack is treating that (for reasons I don't quitey know yet) as a
reassociation and this calls the node cleanup code. The reason it's
seeing a RUN->RUN transition is because during active power save
stuff it's possible that the RUN->SLEEP and SLEEP->RUN transitions
happen so quickly that the deferred net80211 vap state code
"loses" a transition, namely the intermediary SLEEP transition.
So, this was causing the node reassociation code to sometimes be called
twice in quick succession and this would result in ath_tx_tid_cleanup()
to be called again. The code calling it would always call pause, and
then only call resume if the TID didn't have "cleanup_inprogress" set.
Unfortunately it didn't check if it was already set on entry, so it
would pause but not call resume. Thus, paused would be called more
than once (once before each entry into ath-tx_tid_cleanup()) but resume
would only be called once when the cleanup state was finished.
This doesn't entirely fix all of the issues seen in the cleanup path
but it's a necessary first step.
Since this is a stability fix, it should be merged to stable/10 at some
point.
Tested:
* AR5416, STA mode
MFC after: 7 days
Notes:
svn path=/head/; revision=264708
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
tracked BAW actually is.
The net80211 code that completes a BAR will set tid->txa_start (the
BAW start) to whatever value was called when sending the BAR.
Now, in case there's bugs in my driver code that cause the BAW
to slip along, we should make sure that the new BAW we start
at is actually what we currently have it at, not what we've sent.
This totally breaks the specification and so this stays a printf().
If it happens then I need to know and fix it.
Whilst here, add some debugging updates:
* add TID logging to places where it's useful;
* use SEQNO().
Notes:
svn path=/head/; revision=264256
|
| |
|
|
|
|
|
|
|
|
| |
if we've hit the end of the list and cycled around to the first
node again.
Obtained from: DragonflyBSD
Notes:
svn path=/head/; revision=264255
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
match how it's used.
This is another bug that led to aggregate traffic hanging because
the BAW tracking stopped being accurate. In this instance, a filtered
frame that exceeded retries would return a non-error, which would
mean the caller would never remove it from the BAW. But it wouldn't
be added to the filtered list, so it would be lost forever. There'd
thus be a hole in the BAW that would never get transmitted and
this leads to a traffic hang.
Tested:
* Routerstation Pro, AR9220 AP
Notes:
svn path=/head/; revision=264254
|
| |
|
|
| |
Notes:
svn path=/head/; revision=264253
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
we did suspend it.
The whole suspend/resume TID queue thing is supposed to be a matched
reference count - a subsystem (eg addba negotiation, BAR transmission,
filtered frames, etc) is supposed to call pause() once and then resume()
once.
ath_tx_tid_filt_comp_complete() is called upon the completion of any
filtered frame, regardless of whether the driver had aleady seen
a filtered frame and called pause().
So only call resume() if tid->isfiltered = 1, which indicates that
we had called pause() once.
This fixes a seemingly whacked and different problem - traffic hangs.
What was actually going on:
* There'd be some marginal link with crappy behaviour, causing filtered
frames and BAR TXing to occur;
* A BAR TX would occur, setting the new BAW (block-ack window) to seqno n;
* .. and pause() would be called, blocking further transmission;
* A filtered frame completion would occur from the hardware, but with
tid->isfiltered = 0 which indiciates we haven't actually marked
the queue yet as filtered;
* ath_tx_tid_filt_comp_complete() would call resume(), continuing
transmission;
* Some frames would be queued to the hardware, since the TID is now no
longer paused;
* .. and if some make it out and ACked successfully, the new BAW
may be seqno n+1 or more;
* .. then the BAR TX completes and sets the new seqno back to n.
At this point the BAW tracking would be loopy because the BAW
start was modified but the BAW ring buffer wasn't updated in lock
step.
Tested:
* Routerstation Pro + AR9220 AP
Notes:
svn path=/head/; revision=264252
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These are needed to diagnose TX hangs that I and hiren are seeing.
Without it, the only way we'll see debugging is by having ATH_DEBUG_SW_TX
enabled and that is going to be very, very spammy.
ATH_DEBUG_RESET is fine; it's only going to be done during stuck beacon
situations in AP mode.
Whilst I'm here, and now that it's behind debugging, let's just disable
the "print only one" conditional. I'll eventually make it more tunable.
Tested:
* AR9220, hostap mode.
Notes:
svn path=/head/; revision=263454
|
| |
|
|
|
|
|
| |
MFC after: 3 days
Notes:
svn path=/head/; revision=262930
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
Notes:
svn path=/head/; revision=260444
|
| |
|
|
| |
Notes:
svn path=/head/; revision=257270
|
| |
|
|
|
|
|
|
|
|
|
| |
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Notes:
svn path=/head/; revision=257176
|
| |
|
|
| |
Notes:
svn path=/head/; revision=256666
|
| |
|
|
|
|
|
|
| |
Approved by: adrian
MFC after: 2 weeks
Notes:
svn path=/head/; revision=256658
|
| |
|
|
| |
Notes:
svn path=/head/; revision=254435
|
| |
|
|
| |
Notes:
svn path=/head/; revision=251090
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
and if queue mechanism; also fix up (non-11n) TX fragment handling.
This may result in a bit of a performance drop for now but I plan on
debugging and resolving this at a later stage.
Whilst here, fix the transmit path so fragment transmission works.
The TX fragmentation handling is a bit more special. In order to
correctly transmit TX fragments, there's a bunch of corner cases that
need to be handled:
* They must be transmitted back to back, in the same order..
* .. ie, you need to hold the TX lock whilst transmitting this
set of fragments rather than interleaving it with other MSDUs
destined to other nodes;
* The length of the next fragment is required when transmitting, in
order to correctly set the NAV field in the current frame to the
length of the next frame; which requires ..
* .. that we know the transmit duration of the next frame, which ..
* .. requires us to set the rate of all fragments to the same length,
or make the decision up-front, etc.
To facilitate this, I've added a new ath_buf field to describe the
length of the next fragment. This avoids having to keep the mbuf
chain together. This used to work before my 11n TX path work because
the ath_tx_start() routine would be handed a single mbuf with m_nextpkt
pointing to the next frame, and that would be maintained all the way
up to when the duration calculation was done. This doesn't hold
true any longer - the actual queuing may occur at any point in the
future (think ath_node TID software queuing) so this information
needs to be maintained.
Right now this does work for non-11n frames but it doesn't at all
enforce the same rate control decision for all frames in the fragment.
I plan on fixing this in a followup commit.
RTS/CTS has the same issue, I'll look at fixing this in a subsequent
commit.
Finaly, 11n fragment support requires the driver to have fully
decided what the rate scenario setup is - including 20/40MHz,
short/long GI, STBC, LDPC, number of streams, etc. Right now that
decision is (currently) made _after_ the NAV field value is updated.
I'll fix all of this in subsequent commits.
Tested:
* AR5416, STA, transmitting 11abg fragments
* AR5416, STA, 11n fragments work but the NAV field is incorrect for
the reasons above.
TODO:
* It would be nice to be able to queue mbufs per-node and per-TID so
we can only queue ath_buf entries when it's time to assemble frames
to send to the hardware.
But honestly, we should just do that level of software queue management
in net80211 rather than ath(4), so I'm going to leave this alone for now.
* More thorough AP, mesh and adhoc testing.
* Ensure that net80211 doesn't hand us fragmented frames when A-MPDU has
been negotiated, as we can't do software retransmission of fragments.
* .. set CLRDMASK when transmitting fragments, just to ensure.
Notes:
svn path=/head/; revision=251014
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
traffic.
When transmitting non-aggregate traffic, we need to keep the hardware
busy whilst transmitting or small bursts in txdone/tx latency will
kill us.
This restores non-aggregate iperf performance, especially when doing
TDMA.
Tested:
* AR5416<->AR5416, TDMA
* AR5416 STA <-> AR9280 AP
Notes:
svn path=/head/; revision=250866
|
| |
|
|
| |
Notes:
svn path=/head/; revision=250796
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
Notes:
svn path=/head/; revision=250783
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
doesn't match the actual hardware queue this frame is queued to.
I'm trying to ensure that the holding buffers are actually being queued
to the same TX queue as the holding buffer that they end up on.
I'm pretty sure this is all correct so if this complains, it'll be due
to some kind of subtle broken-ness that needs fixing.
This is only done for legacy hardware, not EDMA hardware.
Tested:
* AR5416 STA mode, very lightly
Notes:
svn path=/head/; revision=250735
|
| |
|
|
|
|
|
|
| |
that we are printing out the MAC address in these fields, just printing
out the TID is enough.
Notes:
svn path=/head/; revision=250705
|
| |
|
|
|
|
|
|
| |
This should prevent the TX queue being filled with non-aggregate frames,
causing starvation and non-fair queue behaviour.
Notes:
svn path=/head/; revision=250704
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PS-POLL support.
This implements PS-POLL awareness i nthe
* Implement frame "leaking", which allows for a software queue
to be scheduled even though it's asleep
* Track whether a frame has been leaked or not
* Leak out a single non-AMPDU frame when transmitting aggregates
* Queue BAR frames if the node is asleep
* Direct-dispatch the rest of control and management frames.
This allows for things like re-association to occur (which involves
sending probe req/resp as well as assoc request/response) when
the node is asleep and then tries reassociating.
* Limit how many frames can set in the software node queue whilst
the node is asleep. net80211 is already buffering frames for us
so this is mostly just paranoia.
* Add a PS-POLL method which leaks out a frame if there's something
in the software queue, else it calls net80211's ps-poll routine.
Since the ath PS-POLL routine marks the node as having a single frame
to leak, either a software queued frame would leak, OR the next queued
frame would leak. The next queued frame could be something from the
net80211 power save queue, OR it could be a NULL frame from net80211.
TODO:
* Don't transmit further BAR frames (eg via a timeout) if the node is
currently asleep. Otherwise we may end up exhausting management frames
due to the lots of queued BAR frames.
I may just undo this bit later on and direct-dispatch BAR frames
even if the node is asleep.
* It would be nice to burst out a single A-MPDU frame if both ends
support this. I may end adding a FreeBSD IE soon to negotiate
this power save behaviour.
* I should make STAs timeout of power save mode if they've been in power
save for more than a handful of seconds. This way cards that get
"stuck" in power save mode don't stay there for the "inactivity" timeout
in net80211.
* Move the queue depth check into the driver layer (ath_start / ath_transmit)
rather than doing it in the TX path.
* There could be some naughty corner cases with ps-poll leaking.
Specifically, if net80211 generates a NULL data frame whilst another
transmitter sends a normal data frame out net80211 output / transmit,
we need to ensure that the NULL data frame goes out first.
This is one of those things that should occur inside the VAP/ic TX lock.
Grr, more investigations to do..
Tested:
* STA: AR5416, AR9280
* AP: AR5416, AR9280, AR9160
Notes:
svn path=/head/; revision=250665
|
| |
|
|
|
|
|
| |
pointer values everywhere.
Notes:
svn path=/head/; revision=250611
|
| |
|
|
| |
Notes:
svn path=/head/; revision=250608
|
| |
|
|
| |
Notes:
svn path=/head/; revision=250325
|
| |
|
|
|
|
|
| |
slot is actually NULL.
Notes:
svn path=/head/; revision=249715
|
