2 files changed, 61 insertions, 0 deletions
diff --git a/Bindings/mtd/fsl-quadspi.txt b/Bindings/mtd/fsl-quadspi.txt
new file mode 100644
index 000000000000..823d13412195
--- /dev/null
+++ b/Bindings/mtd/fsl-quadspi.txt
@@ -0,0 +1,35 @@
+* Freescale Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+  - compatible : Should be "fsl,vf610-qspi"
+  - reg : the first contains the register location and length,
+          the second contains the memory mapping address and length
+  - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
+  - interrupts : Should contain the interrupt for the device
+  - clocks : The clocks needed by the QuadSPI controller
+  - clock-names : the name of the clocks
+
+Optional properties:
+  - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
+                              Each bus can be connected with two NOR flashes.
+			      Most of the time, each bus only has one NOR flash
+			      connected, this is the default case.
+			      But if there are two NOR flashes connected to the
+			      bus, you should enable this property.
+			      (Please check the board's schematic.)
+
+Example:
+
+qspi0: quadspi@40044000 {
+	compatible = "fsl,vf610-qspi";
+	reg = <0x40044000 0x1000>, <0x20000000 0x10000000>;
+	reg-names = "QuadSPI", "QuadSPI-memory";
+	interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks VF610_CLK_QSPI0_EN>,
+		<&clks VF610_CLK_QSPI0>;
+	clock-names = "qspi_en", "qspi";
+
+	flash0: s25fl128s@0 {
+		....
+	};
+};
diff --git a/Bindings/mtd/st-fsm.txt b/Bindings/mtd/st-fsm.txt
new file mode 100644
index 000000000000..c2489391c437
--- /dev/null
+++ b/Bindings/mtd/st-fsm.txt
@@ -0,0 +1,26 @@
+* ST-Microelectronics SPI FSM Serial (NOR) Flash Controller
+
+Required properties:
+  - compatible : Should be "st,spi-fsm"
+  - reg        : Contains register's location and length.
+  - reg-names  : Should contain the reg names "spi-fsm"
+  - interrupts : The interrupt number
+  - pinctrl-0  : Standard Pinctrl phandle (see: pinctrl/pinctrl-bindings.txt)
+
+Optional properties:
+  - st,syscfg          : Phandle to boot-device system configuration registers
+  - st,boot-device-reg : Address of the aforementioned boot-device register(s)
+  - st,boot-device-spi : Expected boot-device value if booted via this device
+
+Example:
+	spifsm: spifsm@fe902000{
+	        compatible         = "st,spi-fsm";
+	        reg                =  <0xfe902000 0x1000>;
+	        reg-names          = "spi-fsm";
+	        pinctrl-0          = <&pinctrl_fsm>;
+		st,syscfg	   = <&syscfg_rear>;
+	        st,boot-device-reg = <0x958>;
+	        st,boot-device-spi = <0x1a>;
+		status = "okay";
+	};
+