diff options
Diffstat (limited to 'Bindings/display/panel')
| -rw-r--r-- | Bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt | 26 | ||||
| -rw-r--r-- | Bindings/display/panel/mitsubishi,aa104xd12.txt | 47 | ||||
| -rw-r--r-- | Bindings/display/panel/mitsubishi,aa121td01.txt | 47 | ||||
| -rw-r--r-- | Bindings/display/panel/panel-common.txt | 91 | ||||
| -rw-r--r-- | Bindings/display/panel/panel-dpi.txt | 3 | ||||
| -rw-r--r-- | Bindings/display/panel/panel-lvds.txt | 120 | ||||
| -rw-r--r-- | Bindings/display/panel/samsung,s6e3ha2.txt | 28 | ||||
| -rw-r--r-- | Bindings/display/panel/sitronix,st7789v.txt | 37 | ||||
| -rw-r--r-- | Bindings/display/panel/winstar,wf35ltiacd.txt | 48 |
9 files changed, 447 insertions, 0 deletions
diff --git a/Bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt b/Bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt new file mode 100644 index 000000000000..6812280cb109 --- /dev/null +++ b/Bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt @@ -0,0 +1,26 @@ +Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. + +Required properties: +- compatible: should be "ampire,am-480272h3tmqw-t01h" + +Optional properties: +- power-supply: regulator to provide the supply voltage +- enable-gpios: GPIO pin to enable or disable the panel +- backlight: phandle of the backlight device attached to the panel + +Optional nodes: +- Video port for RGB input. + +Example: + panel_rgb: panel-rgb { + compatible = "ampire,am-480272h3tmqw-t01h"; + enable-gpios = <&gpioa 8 1>; + port { + panel_in_rgb: endpoint { + remote-endpoint = <&controller_out_rgb>; + }; + }; + }; diff --git a/Bindings/display/panel/mitsubishi,aa104xd12.txt b/Bindings/display/panel/mitsubishi,aa104xd12.txt new file mode 100644 index 000000000000..ced0121aed7d --- /dev/null +++ b/Bindings/display/panel/mitsubishi,aa104xd12.txt @@ -0,0 +1,47 @@ +Mitsubishi AA204XD12 LVDS Display Panel +======================================= + +The AA104XD12 is a 10.4" XGA TFT-LCD display panel. + +These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt +with the following device-specific properties. + + +Required properties: + +- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that + order. +- vcc-supply: Reference to the regulator powering the panel VCC pins. + + +Example +------- + +panel { + compatible = "mitsubishi,aa104xd12", "panel-lvds"; + vcc-supply = <&vcc_3v3>; + + width-mm = <210>; + height-mm = <158>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1024x768 @65Hz */ + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hsync-len = <136>; + hfront-porch = <20>; + hback-porch = <160>; + vfront-porch = <3>; + vback-porch = <29>; + vsync-len = <6>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; +}; diff --git a/Bindings/display/panel/mitsubishi,aa121td01.txt b/Bindings/display/panel/mitsubishi,aa121td01.txt new file mode 100644 index 000000000000..d6e1097504fe --- /dev/null +++ b/Bindings/display/panel/mitsubishi,aa121td01.txt @@ -0,0 +1,47 @@ +Mitsubishi AA121TD01 LVDS Display Panel +======================================= + +The AA121TD01 is a 12.1" WXGA TFT-LCD display panel. + +These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt +with the following device-specific properties. + + +Required properties: + +- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that + order. +- vcc-supply: Reference to the regulator powering the panel VCC pins. + + +Example +------- + +panel { + compatible = "mitsubishi,aa121td01", "panel-lvds"; + vcc-supply = <&vcc_3v3>; + + width-mm = <261>; + height-mm = <163>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1280x800 @60Hz */ + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hsync-len = <70>; + hfront-porch = <20>; + hback-porch = <70>; + vsync-len = <5>; + vfront-porch = <3>; + vback-porch = <15>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; +}; diff --git a/Bindings/display/panel/panel-common.txt b/Bindings/display/panel/panel-common.txt new file mode 100644 index 000000000000..ec52c472c845 --- /dev/null +++ b/Bindings/display/panel/panel-common.txt @@ -0,0 +1,91 @@ +Common Properties for Display Panel +=================================== + +This document defines device tree properties common to several classes of +display panels. It doesn't constitue a device tree binding specification by +itself but is meant to be referenced by device tree bindings. + +When referenced from panel device tree bindings the properties defined in this +document are defined as follows. The panel device tree bindings are +responsible for defining whether each property is required or optional. + + +Descriptive Properties +---------------------- + +- width-mm, +- height-mm: The width-mm and height-mm specify the width and height of the + physical area where images are displayed. These properties are expressed in + millimeters and rounded to the closest unit. + +- label: The label property specifies a symbolic name for the panel as a + string suitable for use by humans. It typically contains a name inscribed on + the system (e.g. as an affixed label) or specified in the system's + documentation (e.g. in the user's manual). + + If no such name exists, and unless the property is mandatory according to + device tree bindings, it shall rather be omitted than constructed of + non-descriptive information. For instance an LCD panel in a system that + contains a single panel shall not be labelled "LCD" if that name is not + inscribed on the system or used in a descriptive fashion in system + documentation. + + +Display Timings +--------------- + +- panel-timing: Most display panels are restricted to a single resolution and + require specific display timings. The panel-timing subnode expresses those + timings as specified in the timing subnode section of the display timing + bindings defined in + Documentation/devicetree/bindings/display/display-timing.txt. + + +Connectivity +------------ + +- ports: Panels receive video data through one or multiple connections. While + the nature of those connections is specific to the panel type, the + connectivity is expressed in a standard fashion using ports as specified in + the device graph bindings defined in + Documentation/devicetree/bindings/graph.txt. + +- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible + bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a + phandle to the system I2C controller connected to that bus. + + +Control I/Os +------------ + +Many display panels can be controlled through pins driven by GPIOs. The nature +and timing of those control signals are device-specific and left for panel +device tree bindings to specify. The following GPIO specifiers can however be +used for panels that implement compatible control signals. + +- enable-gpios: Specifier for a GPIO connected to the panel enable control + signal. The enable signal is active high and enables operation of the panel. + This property can also be used for panels implementing an active low power + down signal, which is a negated version of the enable signal. Active low + enable signals (or active high power down signals) can be supported by + inverting the GPIO specifier polarity flag. + + Note that the enable signal control panel operation only and must not be + confused with a backlight enable signal. + +- reset-gpios: Specifier for a GPIO coonnected to the panel reset control + signal. The reset signal is active low and resets the panel internal logic + while active. Active high reset signals can be supported by inverting the + GPIO specifier polarity flag. + + +Backlight +--------- + +Most display panels include a backlight. Some of them also include a backlight +controller exposed through a control bus such as I2C or DSI. Others expose +backlight control through GPIO, PWM or other signals connected to an external +backlight controller. + +- backlight: For panels whose backlight is controlled by an external backlight + controller, this property contains a phandle that references the controller. diff --git a/Bindings/display/panel/panel-dpi.txt b/Bindings/display/panel/panel-dpi.txt index d4add13e592d..6b203bc4d932 100644 --- a/Bindings/display/panel/panel-dpi.txt +++ b/Bindings/display/panel/panel-dpi.txt @@ -9,6 +9,7 @@ Optional properties: - enable-gpios: panel enable gpio - reset-gpios: GPIO to control the RESET pin - vcc-supply: phandle of regulator that will be used to enable power to the display +- backlight: phandle of the backlight device Required nodes: - "panel-timing" containing video timings @@ -22,6 +23,8 @@ lcd0: display@0 { compatible = "samsung,lte430wq-f0c", "panel-dpi"; label = "lcd"; + backlight = <&backlight>; + port { lcd_in: endpoint { remote-endpoint = <&dpi_out>; diff --git a/Bindings/display/panel/panel-lvds.txt b/Bindings/display/panel/panel-lvds.txt new file mode 100644 index 000000000000..b938269f841e --- /dev/null +++ b/Bindings/display/panel/panel-lvds.txt @@ -0,0 +1,120 @@ +LVDS Display Panel +================== + +LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple +incompatible data link layers have been used over time to transmit image data +to LVDS panels. This bindings supports display panels compatible with the +following specifications. + +[JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February +1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA) +[LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National +Semiconductor +[VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video +Electronics Standards Association (VESA) + +Device compatible with those specifications have been marketed under the +FPD-Link and FlatLink brands. + + +Required properties: + +- compatible: Shall contain "panel-lvds" in addition to a mandatory + panel-specific compatible string defined in individual panel bindings. The + "panel-lvds" value shall never be used on its own. +- width-mm: See panel-common.txt. +- height-mm: See panel-common.txt. +- data-mapping: The color signals mapping order, "jeida-18", "jeida-24" + or "vesa-24". + +Optional properties: + +- label: See panel-common.txt. +- gpios: See panel-common.txt. +- backlight: See panel-common.txt. +- data-mirror: If set, reverse the bit order described in the data mappings + below on all data lanes, transmitting bits for slots 6 to 0 instead of + 0 to 6. + +Required nodes: + +- panel-timing: See panel-common.txt. +- ports: See panel-common.txt. These bindings require a single port subnode + corresponding to the panel LVDS input. + + +LVDS data mappings are defined as follows. + +- "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and + [VESA] specifications. Data are transferred as follows on 3 LVDS lanes. + +Slot 0 1 2 3 4 5 6 + ________________ _________________ +Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ +DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< +DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< + +- "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI] + specifications. Data are transferred as follows on 4 LVDS lanes. + +Slot 0 1 2 3 4 5 6 + ________________ _________________ +Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ +DATA0 ><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__>< +DATA1 ><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__>< +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__>< +DATA3 ><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__>< + +- "vesa-24" - 24-bit data mapping compatible with the [VESA] specification. + Data are transferred as follows on 4 LVDS lanes. + +Slot 0 1 2 3 4 5 6 + ________________ _________________ +Clock \_______________________/ + ______ ______ ______ ______ ______ ______ ______ +DATA0 ><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__>< +DATA1 ><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__>< +DATA2 ><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__>< +DATA3 ><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__>< + +Control signals are mapped as follows. + +CTL0: HSync +CTL1: VSync +CTL2: Data Enable +CTL3: 0 + + +Example +------- + +panel { + compatible = "mitsubishi,aa121td01", "panel-lvds"; + + width-mm = <261>; + height-mm = <163>; + + data-mapping = "jeida-24"; + + panel-timing { + /* 1280x800 @60Hz */ + clock-frequency = <71000000>; + hactive = <1280>; + vactive = <800>; + hsync-len = <70>; + hfront-porch = <20>; + hback-porch = <70>; + vsync-len = <5>; + vfront-porch = <3>; + vback-porch = <15>; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds_encoder>; + }; + }; +}; diff --git a/Bindings/display/panel/samsung,s6e3ha2.txt b/Bindings/display/panel/samsung,s6e3ha2.txt new file mode 100644 index 000000000000..18854f4c8376 --- /dev/null +++ b/Bindings/display/panel/samsung,s6e3ha2.txt @@ -0,0 +1,28 @@ +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel + +Required properties: + - compatible: "samsung,s6e3ha2" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - enable-gpios: a GPIO spec for the panel enable pin (active high) + +Optional properties: + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e3ha2"; + reg = <0>; + vdd3-supply = <&ldo27_reg>; + vci-supply = <&ldo28_reg>; + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>; + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>; + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Bindings/display/panel/sitronix,st7789v.txt b/Bindings/display/panel/sitronix,st7789v.txt new file mode 100644 index 000000000000..c6995dde641b --- /dev/null +++ b/Bindings/display/panel/sitronix,st7789v.txt @@ -0,0 +1,37 @@ +Sitronix ST7789V RGB panel with SPI control bus + +Required properties: + - compatible: "sitronix,st7789v" + - reg: Chip select of the panel on the SPI bus + - reset-gpios: a GPIO phandle for the reset pin + - power-supply: phandle of the regulator that provides the supply voltage + +Optional properties: + - backlight: phandle to the backlight used + +The generic bindings for the SPI slaves documented in [1] also applies + +The device node can contain one 'port' child node with one child +'endpoint' node, according to the bindings defined in [2]. This +node should describe panel's video bus. + +[1]: Documentation/devicetree/bindings/spi/spi-bus.txt +[2]: Documentation/devicetree/bindings/graph.txt + +Example: + +panel@0 { + compatible = "sitronix,st7789v"; + reg = <0>; + reset-gpios = <&pio 6 11 GPIO_ACTIVE_LOW>; + backlight = <&pwm_bl>; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + port { + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; +}; diff --git a/Bindings/display/panel/winstar,wf35ltiacd.txt b/Bindings/display/panel/winstar,wf35ltiacd.txt new file mode 100644 index 000000000000..2a7e6e3ba64c --- /dev/null +++ b/Bindings/display/panel/winstar,wf35ltiacd.txt @@ -0,0 +1,48 @@ +Winstar Display Corporation 3.5" QVGA (320x240) TFT LCD panel + +Required properties: +- compatible: should be "winstar,wf35ltiacd" +- power-supply: regulator to provide the VCC supply voltage (3.3 volts) + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. + +Example: + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&hlcdc_pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 31 63 95 127 159 191 223 255>; + default-brightness-level = <191>; + power-supply = <&bl_reg>; + }; + + bl_reg: backlight_regulator { + compatible = "regulator-fixed"; + regulator-name = "backlight-power-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + panel: panel { + compatible = "winstar,wf35ltiacd", "simple-panel"; + backlight = <&backlight>; + power-supply = <&panel_reg>; + #address-cells = <1>; + #size-cells = <0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint { + remote-endpoint = <&hlcdc_panel_output>; + }; + }; + }; + + panel_reg: panel_regulator { + compatible = "regulator-fixed"; + regulator-name = "panel-power-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; |